Disassembly & Inspection

Disassemble / inspect complete engine 150.00

Disassemble short block 100.00

Heads (include disassemble, degrease, inspect) 75.00

Crankshaft (includes clean & mic journals) 40.00

Check / Align / Bore 40.00

Block (includes degrease, measure bores, measure mains) 75.00

Thermal degrease & shotpeen block 65.00

Clean block only (jet wash) 35.00

Thermal degrease & shotpeen heads (one pair) 40.00

Block Work

Bore cylinders up to .060 125.00

Bore cylinders over .060 175.00

Bore and hone cylinders (includes cut for hone reliefs & chamfer) 250.00

Bore and hone cylinders with torque plate up to .060 325.00

Bore and hone cylinders with torque plate over .060 375.00

Touch hone cylinder 125.00

Touch hone cylinders with torque plate 185.00

Cut and true deck heights 155.00

Line hone 2 & 4 bolt blocks 160.00

Line hone block with main girdle 175.00

R&R cam bearings 35.00

R&R core plugs 35.00

Miscellaneous Machine Shop Operations

Shop labor rate per hour 70.00

Degree cam (Adjustments extra) 50.00

Remove broken bolts (15.00 extra for heli coil if needed) 15.00

Deburr block 65.00

Deburr heads 40.00

Polish crank 40.00

Machine o-ring grooves in block & install wire (.041) 200.00

Machine receiver grooves in cylinder heads 150.00

Install Heli coil 15.00

Miscellaneous 'other charge'

Cylinder Head Machining

Competition Valve job 300.00

(includes assamble heads, grind valves, min 3angle on inlet valve,

, radius exhaust seatbackcut intake valves, machine bowls)

*machining for larger valves add $25.00

Install thinwall liners & hone (excludes liners)ea 9.00

Install bronze guides (16) excludes guides 135.00

Install hardened exhaust seats (8) excludes seats ea 15.00

Machining for seals 35.00

Machining for oversize springs 35.00

Deck cut heads (up to .020) 80.00

Angle mill heads (includes cut decks, correct intake face,

ream and spot face bolt holes) 250.00

CC Single chamber 25.00

CC complete head (1) 65.00

Assemble heads with correct spring heights 75.00

Flow one intake and one exhaust port 65.00

Machine for screw-in studs

porting

stage 1 street port blent bowls and entrance to intake 375.00

stage 2 blend bowls, work short turn radi and intake entrance, 650.00

full port ex port

stage 3 full port each cly flowed and checked 1,000.00

Rod & Piston Machining

Reconditioning rods large end 128.00

Pin fit little end 40.00

Pin fit pistons (oversize pins add $10.00) 40.00

Cut down domes 75.00

Cut valve reliefs (inline valve) 125.00

Cut valve reliefs (canted valve) 150.00

File fit rings 128.00

Final clean and assemble pistons and rods 50.00

Balancing

Balance rotating assembly (most) 200.00

Balance crankshaft only (most) 150.00

heavy metal starting at one piece 80.00

Engine Assemby

Check compression (check piston to valve add $50.00) 75.00

Assemble short block (includes fit rod/main/cam bearings,

oil pump, timing chain cover and oil pan) 500.00

Assemble long block (includes short block plus heads, valve

train and inlet manifold) 850.00

High performance engine assembly (includes long block, file fit rings,

degree camshaft, check piston to valve, set or optimize

compression ratio, provide build sheet) 1,250.00

Full competition / race engine Per Estimate Only

Components Subject To Change Due To Availability.

Phone: 586-784-9391 • FAX: 586-473-8091 • Email: stclairengine@aol.com

HOURS: Mon - Fri 9:00 a.m. - 6:00 p.m. Sat. 9:00 a.m. - 12:00 p.m. EST

Components Subject To Change Due To Availability.

Phone: 586-784-9391 • FAX: 586-473-8091 • Email: stclairengine@aol.com

HOURS: Mon - Fri 9:00 a.m. - 6:00 p.m. Sat. 9:00 a.m. - 12:00 p.m. EST

61066d1281095777-kissel-gold-bug-gathering-1923-2